Evergreen has no city hall and no city fence code. It is an unincorporated community in western Jefferson County, about 19 miles west of Denver at roughly 7,162 feet. Jefferson County Planning and Zoning sets the rules, and they read differently from the rules down in the metro.
The headline is simple. The county says it does not require a permit for fences in unincorporated Jefferson County. What it does regulate is where a fence goes, how tall it is near the road, what it is made of in wildfire country, and gates across driveways.
Regal Fencing is a father-and-son company with an office at 3778 S Walden St in Aurora. We don't typically work past the Evergreen area, so this is the western edge of our map. Jackson Vann, the owner and estimator, still comes up for a free on-site estimate and usually sends the written price the same day.
How does Evergreen weather treat a fence?
At about 7,162 feet, Evergreen gets roughly 22 percent more UV than sea level by the World Health Organization's rule of about 10 percent per 1,000 meters. Staining protects wood from Colorado sun and weather, and Regal stains fences as well as building them. Foothills lots also bring slopes and odd shapes, which is what our custom design work is for, and slope and rock both affect the price.
What do Evergreen fence jobs usually involve?
- Split rail, 3-rail ranch and post and rail fences.
- Hog wire fences.
- Steel, aluminum and wrought iron fences.
- Driveway gates: single, double, sliding and custom iron.
- Custom design for slopes and odd-shaped yards.
- Cedar privacy fences where your zone district and covenants allow.
- Repairs to leaning posts and storm damage.
- Fence staining.
Do you need a permit for a fence in Evergreen?
Usually not. Jefferson County's guide, Placing a Fence on a Residential Property, says permits are not required for fences in unincorporated Jefferson County. The county's Outside the Home page says the same.
The fence still has to meet the county's Zoning Resolution. Maximum height comes from your zone district, and Planned Development zones can carry their own specifications.
Check two things before you plan the line. The county advises confirming where the right-of-way line is, and Planning and Zoning can tell you your zone district at 303-271-8700.
County rules are not the only rules. If your subdivision has covenants or an HOA, those apply on top, and we help you put together what its review asks for.
How tall can a fence be near the road in Evergreen?
42 inches is the number to remember. No fence over 42 inches can be located within the required front setback of the applicable zone district, according to the county's guide.
The same 42 inch limit applies inside the county's vision clearance triangle, the corner area drivers need to see across.
Walls count. A fence on top of a retaining wall is measured as the wall plus the fence, and the total can't exceed the maximum for the zone district. Retaining walls over 36 inches need a permit of their own.
Does a driveway gate need a permit in Evergreen?
Often, yes. Jefferson County requires a Miscellaneous Permit for any gate across an access that serves a parcel, tract or lot.
Your fire protection district has to approve the gate before the county issues that permit.
Regal builds single, double, sliding and custom iron gates. Tell us at the estimate if the gate crosses your driveway, so the permit and the fire district approval are in the plan from the start.
What do wildfire rules mean for a fence in Evergreen?
Jefferson County says fences and gates in its Wildland Urban Interface Overlay must comply with the material regulations in the county's Wildfire Resiliency Code.
The county's fence guide lists metal and masonry among the acceptable materials.
That can mean a steel, aluminum or wrought iron section where the fence meets the house, with wood farther out. Check whether your lot is in the overlay on the county's map, and confirm the material with Planning and Zoning before we order.
How does Regal work in Evergreen?
We request the Colorado 811 utility locate before digging. State law requires at least 2 business days' notice, and Colorado 811 asks for 3.
Most installs take 1 to 2 days, with crews of 2 to 3. Any sprinkler line we damage during the install is fixed for free.
